When it comes to waterproofing concrete slabs, masonry walls, landscaping stone, exposed aggregate, clay brick, saltillo tile, stucco, colored concrete, stained concrete, natural stone and other porous substrates – Lifeguard Waterproofing Products are your best choice.

Question:  Can Lifeguard 30 be applied on new concrete?
Answer:  Yes, we recommend that Lifeguard be applied to concrete after the initial release of water or approximately 21  days after the pour. A smooth steel trowel finish will need to be slightly etched with Lifeguard’s new Efflorescence Remover.

Question:  Are cleaners recommended to prepare the surface before applying the Lifeguard 30?
Answer:  Yes, using Lifeguard’s new Concrete Cleaner & Degreaser will remove any contaminants from the surface.  However, before application, allow the surface to dry and always test a small area to ensure penetration and aesthetics.

Question:  What PSI should be used after applying Lifeguard Efflorescence Remover?
Answer:  A minimum of 2000 PSI should be used to rinse the surface.

Question:  Does Lifeguard 30 have a glossy appearance after it has been dried?
Answer:  No, Lifeguard 30 is designed to have a matte finish.  However, a slight enhancement of color will occur.  Please note: A minimum of 24 hours must elapse to determine degree of enhancement.

Question:  Can Lifeguard 30 be applied to colored concrete?
Answer:  Yes, Lifeguard 30 can be applied to an integral colored concrete as long as any curing compounds are removed by power washing.

Question: Can Lifeguard 30 be used as a graffiti control?
Answer:  Yes, Lifeguard must be applied in two coats at least 30 minutes between coats.  Graffiti can be removed by pressure washing the surface up to two cycles.

Question:  Can Lifeguard 30 protect against leaks in mortar joints?
Answer:  Yes, the RTV Rubber in Lifeguard is very effective in sealing hairline cracks up to 1/16 of an inch.  Any larger cracks should be caulked.

Question:  After applying Lifeguard 30, can the surface be painted?
Answer:  No, the liquid rubber in Lifeguard’s 30 Year Waterproofing Sealant will prevent paint from sticking to the surface.

Question:  Will Lifeguard 30 make a surface slippery?
Answer:  No, Lifeguard 30 Year Waterproofing Sealant is designed to penetrate into the surface. Please note: concrete paint, stains or sealers applied previously must be removed prior to the application to ensure adequate penetration.

Question:  Can the Lifeguard 30 be applied over paint or concrete stain?
Answer:  No, Lifeguard 30 Year Waterproofing Sealant needs a surface that is free of any previously applied paints, stains or sealers.

Question:  Should Lifeguard 30 be used as an oil repellent?
Answer:  No, we recommend that Lifeguard be used as intended.  Any oil should be cleaned from the surface within a few days.  If stains remain, use Lifeguard Concrete Cleaner & Degreaser to remove.

Question:  Should I use Lifeguard 30 in a fishpond or birdbath?
Answer:  No, it’s not intended to be used where hydrostatic pressure is present or if the surface will be submerged in water.

Question:  Should Lifeguard Wet Look Gloss be applied to a hot surface?
Answer:  No, the solvent in Wet Look Gloss will flash-off preventing proper adhesion of the product.

Question:  Can I apply more than two coats of Wet Look Gloss?
Answer:   Yes, however, make sure that your first coat is very light.  Wait 60 minutes before applying the second coat.  After an additional 60 minutes, determine if a third coat is necessary by testing an area.

Question:  Can I add an anti-slip additive to Wet Look Gloss?
Answer:  Yes, you can use Lifeguard Croc-Grip. Just make certain the guidelines are followed.